MANURE PUMPS - PATZ       Patz Model 1512 Manure Pump Plunger Size: 7 x 15 in. Stroke Lengths: 20 in., 17 in. and 14 in. Hole Size for Pump Installation: 5 ft. wide x 14 ft. long x 7 ft. 3in. deep (approximately) Floor Space Required for Pump: 3 ft. 2 in. x 11 ft. (approximately) Weight: 2,350 lb. (approximately) Safety Railing: Standard equipment Pipe Length: Recommended maximum length of pipe with no elbows, 150 ft. Deduct 5 ft. for each 22-1/2° elbow used and 10 ft. for each 45° elbow. Up to 90° of elbows may be used in one installation Pipe Size: Choose 15" or 12" PVC pipe Storage Height (Head): Maximum storage height (head) is 25 ft. This is measured from center line of pipe at manure pump to top of manure in storage area    Patz Model 3333 Multi-Use Vertical Pump Tapered-bore drive pulley mounts to a 1-1/8-inch (29 mm) drive shaft with a greaseable flange bearing at the top of the drive tube Easy access to oil reservoir High-volume delivery Protection against bearing contamination Bearing seals can be purged every 8 hours thanks to a grease line from the seal pack to the top of the pump Clogging prevented and positive input provided Shear plate has two legs to help support pump off the floor of the pit Impeller transition area features beefed-up steel for long life Pump available in various lengths to fit pit depths of 3 12 feet    Patz Model 4444 Vertical Pit Pump Pumping capacity up to 1,580 gals./min Available in lengths to fit your application: 6 ft. (1.8 m), 8 ft. (2.4 m), 10 ft. (3.0 m), and 12 ft. (3.6 m) A 16-inch (40.6 cm) Impeller for added capacity Variable agitation capacities with a standard dual agitation system Abrasion-resistant steel in high wear areas for longer life Tapered-bore drive pulley mounts to a 1-3/4 inch (44.5 mm) drive shaft with a greaseable flange bearing at the top of the drive tube Easy access to oil reservoir Lifting loops located on top of the pump allows easy insertion and removal of the unit from the pit with a tractor loader, skid-steer loader or winch A steel mounting plate is included as standard equipment to allow precise positioning of the pump to match the pit depth. Plate can be lagged to a concrete pad or curb Pump available in various lengths to fit pit depths of 5 ft. 6 in. (1.7 m) to 12 ft 10 in. (3.9 m)    6000 & 8000 PTO Drive Vertical Pit Pumps Stationary base secured to manure pit or two-point tractor hitch with hydraulics for tilting Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m) Large U-bolts allow the frame to be adjusted up or down for precise placement Match your desired speed of transfer and loading with two pump sizes: 6-inch (152 mm) and 8-inch (203 mm) pipe Reduce agitation time with dual nozzles that blend crusted manure and settled solids into a liquid slurry fast Get better pit clean out by agitating every corner with adjustable nozzles (rotate both horizontally and vertically) Remove clumps of straw with chopping action over impeller shredder plate Lower repair costs with impeller housing of abrasion-resistant steel in high-wear areas Tractor Requirement: 100 HP minimum Model 6000E Electric Drive Vertical Pit Pump A stationary base secured to manure pit is standard on the 6000E Pump Equipped with a two-point tractor hitch for easy insertion and removal from pit for service Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m) Large U-bolts allow the frame to be adjusted up or down for precise placement Get better pit clean-out by agitating with a nozzle which can be rotated horizontally Save time when agitating, transferring, and loading due to swept-back impeller blades for high-volume pumping up to 2,500 gallons per minute-during agitation and 2200 gallons per minute during loading Horsepower Requirements: Twin 15, 20, 25, or 30 HP, 3-phase motors    Patz Model 9000 Liquid Transfer System Pump: 1/2 hp. 1625 RPM: Single phase; 230 volts; 5.8 amps; 84 lb. (38 kg); maximum solids diameter: 2" (50.8 mm); two-vane, non-clogging impellers Pump Performance: G.P.M. at total head in feet Gutter Widths: 15" to 20" Hole Size for Installation: 18" (457 mm) wide x 24" (610 mm) long x 30" (762 mm) depth below gutter bottom (20 gal. sump) Pipe Size: 2" (50.8 mm) PVC schedule 40 Pipe supports should be every 10' (3m) apart Height to top of handle: 19-3/8" Width at widest point: 12-5/8" Discharge: 2 NPT Suction inlet opening: 2" Weight: 84 lb.